Space Technology Assembly

Photos of technicians working on NASA's space launch systems, showcasing advanced engineering and assembly processes in well-equipped facilities.

Detail, snapshot of a paper mill Detail, snapshot of a paper mill

Switzerland, Geneva, ATLAS Cavern, CERN

CAPE CANAVERAL, Fla. - Motion of the segments of a new crane is tested inside the Operations and Checkout Building at NASA's Kennedy Space Center in Florida. The new O&C low-bay crane is a 25-ton overhead bridge crane built for Lockheed Martin and Space Florida by American Crane and Equipment Corporation in Douglasville, Pa. The crane has a bridge span of 78-2” and a hook height of 48-10”. The crane will be used for lifting and moving flight hardware, fixtures and equipment in support of the Orion spacecraft manufacturing. Part of NASA's Constellation Program, the Orion spacecraft will return humans to the moon and prepare for future voyages to Mars and other destinations in our solar system.

Interior View of Orbiter Processing Facility 3

CAPE CANAVERAL, Fla. ---In Orbiter Processing Facility Bay 3 at NASA's Kennedy Space Center, space shuttle Discovery's second payload bay door is nearly closed. Discovery is the designated vehicle on the STS-124 mission to the International Space Station. On the mission, the shuttle will transport the Kibo Japanese Experiment Module - Pressurized Module and the Japanese Remote Manipulator System. The payload will be installed at the launch pad. Launch is targeted for May 25.

CAPE CANAVERAL, Fla. - Inside Orbiter Processing Facility-1 at NASAs Kennedy Space Center in Florida, United Space Alliance technicians monitor the progress of space shuttle Atlantis payload bay doors as they are closed in preparation for its move to the Vehicle Assembly Building.The work is part of the Space Shuttle Programs transition and retirement processing of the space shuttle fleet. A groundbreaking was held Jan. 18 for Atlantis future home, a 65,000-square-foot exhibit hall in Shuttle Plaza at the Kennedy Space Center Visitor Complex. Atlantis is scheduled to roll over to the visitor complex in November in preparation for the exhibits grand opening in July 2013.

NASA engineers install test hardware for the agency's new heavy lift rocket, the Space Launch System, into a newly constructed 50-foot structural test stand at NASA's Marshall Space Flight Center. In the stand, hydraulic cylinders will be electronically controlled to push, pull, twist and bend the test article with millions of pounds of force. Engineers will record and analyze over 3,000 channels of data for each test case to verify the capabilities of the engine section and validate that the design and analysis models accurately predict the amount of loads the core stage can withstand during launch and ascent. The engine section, recently delivered via NASA's barge Pegasus from NASA's Michoud Assembly Facility, is the first of four core stage structural test articles scheduled to be delivered to Marshall for testing. The engine section, located at the bottom of SLS's massive core stage, will house the rocket's four RS-25 engines and be an attachment point for the two solid rocket boos

VANDENBERG AFB, California - The transportation canister is removed from around NASA's SMAP spacecraft after positioning the satellite atop a Delta II rocket at Space Launch Complex-2 for launch. For more, go to www.nasa.gov/smap

Elevated view of building interior with ongoing boat refurbishment. Boathouse 4, Portsmouth, United Kingdom. Architect: Walters and Cohen Ltd, 2015.

. These images and videos show technicians at NASAs Michoud Assembly Facility in New Orleans lifting and installing the liquid oxygen dome weld confidence article for a future upper stage for NASAs SLS (Space Launch System) rocket onto the LTAC (LOX Tank Assembly Center) in Building 115 at Michoud for the next phase of manufacturing in July 2023. The dome makes up a portion of the liquid oxygen tank weld confidence article for the EUS (exploration upper stage). Teams use weld confidence articles to verify welding procedures and structural integrity of the welds to manufacture structural test and flight versions of the hardware. EUS flight hardware is in early production at Michoud. The more powerful upper stage and its four RL10 engines will be used on the second configuration of the SLS rocket, known as Block 1B, and will provide in-space propulsion to send astronauts in NASAs Orion spacecraft and heavy cargo on a precise trajectory to the Moon. NASA and Boeing, the lead contractor fo

Hot steel coming out of a blast furnace

CAPE CANAVERAL, Fla. -- In the Assembly and Refurbishment Facility at NASA's Kennedy Space Center in Florida, the forward skirt extension of the Ares I-X first stage is lowered onto a work stand. The extension will house new, larger parachutes. The three main parachutes each have a 150-foot diameter, compared to the shuttle booster main parachutes, which are 136 feet across.

Two NASA Space Launch System (SLS) solid rocket boosters are readied for mating to the rockets two aft skirts on June 16, 2020, inside Kennedy Space Centers Rotation, Processing and Surge Facility. Together, the twin boosters provide more than 75 percent of the total SLS thrust at launch. Manufactured by Northrop Grumman in Promontory, Utah, the boosters arrived at Kennedy via train. The cross-country journey was an important milestone for the agencys Artemis I launch. The first in a series of increasingly complex missions, Artemis I will test the Orion spacecraft and SLS as an integrated system prior to crewed missions to the Moon. Once the boosters are mated with the aft skirts, they will be moved to the Vehicle Assembly Building for stacking on the mobile launcher.

Scrubbers in A Coal-Fired Power Station 1074706765

Worker with safety helmet. Worker with safety helmet at industrial factory

UTIL DE MONTAJE DE AVION MERCURE. Location: Casa. Sevilla. Seville. SPANIEN.

VANDENBERG AIR FORCE BASE, Calif. - The stage 0 motor, left, and the interstage associated with Stage 1 of the Taurus XL rocket are ready for more processing in the west high bay of Building 1555 at Vandenberg Air Force Base in California. In the east high bay, right, are the first, second and third stages. The rocket and NASA's Glory satellite are being prepared for a launch to low Earth orbit from Vandenberg's Space Launch Complex 576-E.Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate.

Electrical Power Plant, Gas Turbine Generator And Drive Shaft, Prudhoe Bay, Arctic Alaska, USA, Summer

Belgium, Antwerp city, tunnel boring, metal pillar

NASA Moves Core Stage 3 Intertank. Technicians at NASAs Michoud Assembly Facility move the intertank of NASAs Space Launch System rocket for Artemis III to Cell G on October 26, 2022 to await application of the thermal protection system. Thermal protection systems protect space vehicles from aerodynamic heating during entry to planet atmosphere and re-entry to earth atmosphere. The intertank lays between the liquid hydrogen tank and liquid oxygen tank. Together with the engine section and the forward skirt, they comprise the SLS core stage. The liquid hydrogen tank and liquid oxygen tank hold 733,000 gallons of propellant to power the stages four RS-25 engines needed for liftoff and Artemis missions to the Moon and future missions to Mars. Image credit: NASA/Michael DeMocker

Construction site of the new hydropower plant in Rheinfelden, shaft 3, positioning the impeller, 6.5 metres in diameter and weighing 40 tons, Rheinfelden - Ost, Rheinfelden - Baden, Baden-Wuerttemberg, Germany, Europe

KENNEDY SPACE CENTER, FLA. -- Inside Discovery's opened payload bay, a technician installs a wiring modification called the "Station to Shuttle Power Transfer System," or SSPTS. The SSPTS allows the space shuttle to stay docked at the International Space Station longer by providing its power and preserving its consumables. Other workers oversee the operation. Discovery is scheduled to fly on mission STS-122 to the International Space Station in the fall of 2007.

Engine installation in Oberhausen pumping station, new construction of Emscher sewer, Emscher conversion, Ruhr area, Oberhausen, North Rhine-Westphalia, Germany, Europe

USA, Louisiana, Atchafalaya Basin. Old River Navigational Lock, built and maintained by the US Army Corps of Engineers.

CAPE CANAVERAL, Fla. - Motion of the segments of a new crane is tested inside the Operations and Checkout Building at NASA's Kennedy Space Center in Florida. The new O&C low-bay crane is a 25-ton overhead bridge crane built for Lockheed Martin and Space Florida by American Crane and Equipment Corporation in Douglasville, Pa. The crane has a bridge span of 78-2” and a hook height of 48-10”. The crane will be used for lifting and moving flight hardware, fixtures and equipment in support of the Orion spacecraft manufacturing. Part of NASA's Constellation Program, the Orion spacecraft will return humans to the moon and prepare for future voyages to Mars and other destinations in our solar system.

Interior of industrial plant. CoppenHill Power Plant, Copenhagen, Denmark. Architect: BIG Bjarke Ingels Group, 2019.

DAVID OSBORNE, A MACHINIST ON THE METTS CONTRACT, OPERATES THE 7-AXIS MILLING MACHINE WITH CF1 BARREL BEING PREPARED FOR SHELL BUCKLE TESTING

Local people enjoying a thrilling ride on the caterpillar roller coaster at the Kaeson Youth Park, North Korea

View of the synchrotron or circular particle accelerator of a hadrontherapy center for cancer treatment.

5TH SBKF (SHELL BUCKLE KNOCKDOWN FACTOR) WORKSHOP, MSFC, FEB. 3-4, 2015

Royal Opera House Production Workshop, Purfleet, United Kingdom. Architect: Nicholas Hare Architects LLP, 2013. Elevated view from set gallery with set designers airbrushing.

Detail of the blast furnace group of Volklinger Hutte (Volklingen Ironworks), Volklingen, Germany

A900680 U12N MINERAL QUARRY INSTRUMENTATION RACKS JOHN ALLEN (Project Engineer) JUL 19 90 EG&G/NTS PHOTO LAB Publication Date: 7/19/1990 CABLES; CABLES & WIRES; EDGERTON, GERMESHAUSEN & GRIER; EG&G; INSTRUMENTATION RACKS; MINERAL QUARRY; N-TUNNEL; NEVADA; NEVADA TEST SITE; NTS; NUCLEAR ENERGY TECHNOLOGY; RACKS; TEST SITES; TUNNELS; UGT; UNDERGROUND TESTING; WEAPONS EFFECTS; WIRE & CABLES historical images. 1972 - 2012. Department of Energy. National Nuclear Security Administration. Photographs Related to Nuclear Weapons Testing at the Nevada Test Site.

On Thursday 8th October 2020, Florence Parly, Minister of the Armed Forces, visits two defence companies essential to the economic fabric of the Brittany region. The Minister of the Armed Forces first visits SOCARENAM, a French shipbuilding company, where she will visit the construction site of an overseas patrol boat (POM). The design and construction of the six POMs represent, on SOCARENAM's sites and for its many subcontractors in France, between 500 and 600 highly qualified jobs that cannot be relocated. Saint-Malo on 2020-10-08.Le jeudi 8 octobre 2020, Florence Parly, ministre des Armees, visite deux entreprises de defense essentielles au tissu economique de la region Bretagne. La ministre des Armees se rend dabord au sein de lentreprise SOCARENAM, entreprise française de construction navale, ou elle visite le chantier de la construction dun patrouilleur outre-mer (POM). La conception et la construction des six POM representent, sur les sites de SOCARENAM et pour ses nombreux

7-AXIS MILLING MACHINE PERFORMING THE ROUGH CUT ON THE 2ND QUARTER DOME DEMONSTRATION ARTICLE HONEYCOMB CORE

Lift shaft Modern elevator shaft interior with cables and tracks Copyright: xZoonar.com/MarkoxBericx 6999294

jsc2021e004398 (Jan. 21, 2021) --- Internal view of the Sierra Nevada Dream Chaser mockup located in Building 9N, Space Vehicle Mockup Facility (SVMF) at the NASA Johnson Space Center.

Old Elbe Tunnel or St. Pauli Elbe Tunnel Alter Elbtunnel, St. Pauli Elbtunnel, View from the ground of the tunnel to the top, south exit Hamburg Hamburg Germany

Worker working on an electrical power plant, gas turbine generator and drive shaft, Prudhoe Bay, Arctic Alaska, USA, Summer

The completed barrel and aft bulkhead of the Orion Artemis I pressure vessel at NASA's Michoud Assembly Facility in New Orleans on Nov. 15, 2015. Part of Batch image transfer from Flickr.

Engineers lift the Orion Crew Module Adapter Structural Test Article into the test stand at NASA Glenn Research Center Plum Brook Facility on Sept. 23, 2015. Part of Batch image transfer from Flickr.

View of the synchrotron or circular particle accelerator of a hadrontherapy center for cancer treatment.

IRIS/Pegasus Motor Arrival

CAPE CANAVERAL, Fla. - Inside the Vehicle Assembly Building, or VAB, at NASA's Kennedy Space Center in Florida, the 175-ton crane is being lowered from Level 16 down to the transfer aisle floor. Upgrades to the crane's 45-year-old controls will be performed in order to improve reliability, precision and safety. The Ground Systems Development and Operations Program is overseeing upgrades and modifications to the VAB. The crane will be upgraded so that it can support lifting needs for NASA and other exploration vehicles, including the agency's Space Launch System and Orion spacecraft.

The spawning room at the Spring Creek National Fish Hatchery. Subjects: Fish hatcheries; Fisheries management; Fishes; Employees (USFWS); Biologists (USFWS); Work of the Service. Location: Washington. Fish and Wildlife Service Site: SPRING CREEK NATIONAL FISH HATCHERY.

Interior view of Launch Pad 39A

Machine and equipment in the weaving shop. interior of industrial textile factory. loom. weaving workshop at the factory

ARES 7 AXIS MILLING EQUIPMENT AND FACILITIES.

KENNEDY SPACE CENTER, Fla. -- In the Orbiter Processing Facility bay 3, with the help of a crane, workers check the placement of a main bus switching unit in Discovery's payload bay. A main bus switching unit is used for power distribution, circuit protection and fault isolation on the space station's power system. The units route power to proper locations in the space station, such as from solar arrays through umbilicals into the U.S. Lab. The unit will be installed on the external stowage platform 2 attached to the Quest airlock for temporary storage. Discovery is targeted to launch mission STS-120 no earlier than Oct. 20.

A view of the new work platforms in High Bay 3 of the Vehicle Assembly Building on Feb. 22, 2019, at NASAs Kennedy Space Center in Florida. Preparations are underway to perform an initial swing test of the Core Stage Inter-tank Umbilical (CSITU) on the mobile launcher. The CSITU is a swing-arm umbilical that will connect to the Space Launch System core stage inter-tank. It will provide conditioned air, pressurized gases and power and data connection to the core stage. Exploration Ground Systems at Kennedy is conducting the swing test.

A view of the FRAME 86 of the Avenger class mine countermeasures ship SCOUT (MCM-8) during construction at the Peterson Builders, Inc. shipyard. Base: Sturgeon Bay State: Wisconsin (WI) Country: United States Of America (USA)

KENNEDY SPACE CENTER, FLA. -- Technicians prepare to join the Pressurized Mating Adapter (PMA)-2, seen here in its yellow workstand at right, to Node 1 (the International Space Stations [ISS structural building block) in KSCs Space Station Processing Facility. This PMA is a cone-shaped connector to Node 1, which will have two PMAs attached once PMA-2 is mated with the node. The node and PMAs, which together will make up the first element of the ISS, are scheduled to be launched aboard the Space Shuttle Endeavour on STS-88.

The second of three aeroshells, at right, for Orion's Launch Abort System (LAS) was lifted up from a flatbed truck and secured in High Bay 4 of the Vehicle Assembly Building at NASA's Kennedy Space Center in Florida, on June 26, 2018. The aeroshell was shipped from EMF Inc. on nearby Merritt Island. The aeroshells will be stacked and prepared for a full-stress test of the LAS, called Ascent Abort-2 (AA-2) flight test, scheduled for April 2019. During the test, a booster will launch from Space Launch Complex 46 at Cape Canaveral Air Force Station, carrying a fully functional LAS and a 22,000-pound Orion test vehicle to an altitude of 31,000 feet and traveling at more than 1,000 miles an hour. The test will verify the LAS can steer the crew module and astronauts aboard to safety in the event of an issue with the Space Launch System (SLS) rocket when the spacecraft is under the highest aerodynamic loads it will experience during a rapid climb into space. Orion is being prepared for its fi

In this aerial view, teams with NASAs Exploration Ground Systems and contractor Jacobs lift the Space Launch System (SLS) core stage - the largest part of the rocket - and prepare to move it over to High Bay 3 in the Vehicle Assembly Building, where it will be placed atop the mobile launcher in between the twin solid rocket boosters, at NASAs Kennedy Space Center in Florida on June 10, 2021. The 188,000-pound core stage, with its four RS-25 engines, will provide more than 2 million pounds of thrust during launch and ascent, and coupled with the boosters, will provide more than 8.8 million pounds of thrust to send the Artemis I mission to space. Under the Artemis program, NASA will land the first woman and first person of color on the Moon, as well as establish a sustainable presence on the lunar surface in preparation for human missions to Mars.

UTIL DE MONTAJE DE AVION. Location: Casa. Sevilla. Seville. SPANIEN.

KENNEDY SPACE CENTER, FLA. - At Launch Complex 17-A, Cape Canaveral Air Force Station, the first half of the fairing for the Mars Exploration Rover 2 (MER-2/MER-A) is moved inside the launch tower. The fairing will be installed around the payload for protection during launch. The MER Mission consists of two identical rovers designed to cover roughly 110 yards each Martian day over various terrain. Each rover will carry five scientific instruments that will allow it to search for evidence of liquid water that may have been present in the planet's past. Identical to each other, the rovers will land at different regions of Mars. Launch date for MER-A is scheduled for June 5..

In High Bay 4 of the Vehicle Assembly Building (VAB) at NASAs Kennedy Space Center in Florida, one of the Artemis I aft booster segments for the Space Launch System is being prepared for its lift up and lowering onto the mobile launcher in High Bay 3 for stacking operations on Nov. 20, 2020. Workers with Exploration Ground Systems and contractor Jacobs teams will stack the twin five-segment boosters on the mobile launcher in High Bay 3 over a number of weeks. When the core stage arrives, it will join the boosters on the mobile launcher, followed by the interim cryogenic propulsion stage and Orion spacecraft. Manufactured by Northrop Grumman in Utah, the twin boosters provide more than 75 percent of the total SLS thrust at launch. The SLS is managed by Marshall Space Flight Center in Huntsville, Alabama. Under the Artemis program, NASA will land the first woman and the next man on the Moon by 2024. The first in a series of increasingly complex missions, Artemis I will test the Orion sp

KODIAK ISLAND, Alaska -- Technicians install Orbis 21D Equipment Section Boost Motor, the second stage of the Athena 1 launch vehicle, at Kodiak Island, Alaska, as processing for the launch of Kodiak Star proceeds. The first orbital launch to take place from Alaska's Kodiak Launch Complex, Kodiak Star is scheduled to lift off on a Lockheed Martin Athena I launch vehicle on Sept. 17 during a two-hour window that extends from 5 00 to 7 00 p.m. ADT. The payloads aboard include the Starshine 3, sponsored by NASA, and the PICOSat, PCSat and Sapphire, sponsored by the Department of Defense (DoD) Space Test Program.

The second of three aeroshells, at right, for Orion's Launch Abort System (LAS) was lifted up from a flatbed truck and secured in High Bay 4 of the Vehicle Assembly Building at NASA's Kennedy Space Center in Florida, on June 26, 2018. The aeroshell was shipped from EMF Inc. on nearby Merritt Island. The aeroshells will be stacked and prepared for a full-stress test of the LAS, called Ascent Abort-2 (AA-2) flight test, scheduled for April 2019. During the test, a booster will launch from Space Launch Complex 46 at Cape Canaveral Air Force Station, carrying a fully functional LAS and a 22,000-pound Orion test vehicle to an altitude of 31,000 feet and traveling at more than 1,000 miles an hour. The test will verify the LAS can steer the crew module and astronauts aboard to safety in the event of an issue with the Space Launch System (SLS) rocket when the spacecraft is under the highest aerodynamic loads it will experience during a rapid climb into space. Orion is being prepared for its fi

Businesswoman standing by colleague on staircase at power station

DA-SC-89-07783. Base: Rock Island State: Illinois (IL) Country: United States Of America (USA)

Galvanizing steel. Production of zinc-coated steel

Clean Ladle of molten steel inside of steel plant

Gold mine processing plant equipment is seen from the inside

CAPE CANAVERAL, Fla. -- In the Vehicle Assembly Building at NASA's Kennedy Space Center in Florida, workers observe the external fuel tank, ET-122, for space shuttle Endeavour's STS-134 mission, as it is lifted from its test cell. When lowered in place, the tank will be attached to the solid rocket boosters on the mobile launcher platform. Endeavour and its crew will deliver the Express Logistics Carrier-3 and the Alpha Magnetic Spectrometer to the International Space Station. Launch is targeted for April 19.

Turbinen und Generatoren in einem Kohlekraftwerk *** Turbines and Generators in a Coal-fired power station 1074706454

Water sprays on the Crew Access Arm during a deluge systems test March 23 at a construction yard near NASA's Kennedy Space Center in Florida. The arm is being tested before being installed on Space Launch Complex 41 Crew Access Tower later this year. It will be used as a bridge by astronauts to board Boeing's CST-100 Starliner spacecraft as it stands on the launch pad atop a United Launch Alliance Atlas V rocket.

CAPE CANAVERAL, Fla. - As part of NASA's Ground Systems Development and Operations Program at the Kennedy Space Center in Florida, a large space shuttle-era work platform is being removed from high bay 3 of the Vehicle Assembly Building, or VAB. The work is part of a center-wide modernization and refurbishment initiative to accommodate NASAs Space Launch System and a variety of other spacecraft instead of the whole building supporting one design. Visible in the lower-left background is the space shuttle Atlantis being readied for its move to the Kennedy Space Center Visitor Complex. The Ground Systems Development and Operations Program is developing the necessary ground systems, infrastructure and operational approaches required to safely process, assemble, transport and launch the next generation of rockets and spacecraft in support of NASAs exploration objectives. Future work also will replace the antiquated communications, power and vehicle access resources with modern efficien

This image, taken on Oct. 9, 2019, at NASA's Jet Propulsion Laboratory in Pasadena, California, captures the move of the Mars 2020 rover into a large vacuum chamber for testing in Mars-like environmental conditions. Movie available at

Interior View of Orbiter Processing Facility 3

The American flag and a small tree are in view on the final work platform, A north, as the platform is lifted up by crane from the transfer aisle in the Vehicle Assembly Building (VAB) at NASA's Kennedy Space Center in Florida. The platform will be installed and secured on its rail beam high up on the north wall of High Bay 3. The installation of the final topmost level completes the 10 levels of work platforms, 20 platform halves altogether, that will surround NASA's Space Launch System rocket and the Orion spacecraft and allow access during processing for missions, including the first uncrewed flight test of Orion atop the SLS rocket in 2018. The A-level platforms will provide access to the Orion spacecraft's Launch Abort System for Orion lifting sling removal and installation of the closeout panels. The Ground Systems Development and Operations Program, with support from the center's Engineering Directorate, is overseeing upgrades and modifications to the VAB, including installation

The high bay inside the Neil Armstrong Operations and Checkout Building at NASAs Kennedy Space Center in Florida, is being readied on March 3, 2021, for installation of a new crane. The new overhead crane will be used to process Orion beginning with the agencys first crewed mission, Artemis II. Teams from American Crane and Equipment Corp. replaced the Lypta 27.5-ton crane (pictured) with the new Artemis-rated 30-ton crane. The new crane will have enhanced controls and additional safety features that will allow for micro movements to within 1/100th of an inch. Operators will use the crane to lift Orion once the crew and service modules are mated.

The S-I stages for the Saturn I (SA-1 at right and SA-2 at left) are being assembled at the Marshall Space Flight Center, building 4705. The Saturn I S-I stage had eight H-1 engines clustered, using liquid oxygen/kerosene-1 (LOX/RP-1) propellants capable of producing a total of 1,500,000 pounds of thrust.

Engine installation in Oberhausen pumping station, new construction of Emscher sewer, Emscher conversion, Ruhr area, Oberhausen, North Rhine-Westphalia, Germany, Europe

Interior View of Orbiter Processing Facility 3

A740125A U12N MING BLADE FAST GATE BILL BLYTHE (Project Engineer) JAN 29, 1974EG&G/NTS PHOTO LAB Publication Date: 1/29/1974 BLADES; BLYTHE, BILL; EDGERTON, GERMESHAUSEN & GRIER; EG&G; EQUIPMENT & INSTRUMENTS; FAST GATE; MING BLADE TEST; NEVADA; NEVADA TEST SITE; NTS; NUCLEAR ENERGY TECHNOLOGY; NUCLEAR TESTING; NUCLEAR TESTS; TEST SITES; U12N; U12N MING BLADE; UGT; UNDERGROUND TESTING historical images. 1972 - 2012. Department of Energy. National Nuclear Security Administration. Photographs Related to Nuclear Weapons Testing at the Nevada Test Site.

Worker Working On An Electrical Power Plant, Gas Turbine Generator And Drive Shaft, Prudhoe Bay, Arctic Alaska, USA, Summer

Delta II/GRAIL Fairing Installation

Dairy farming, Alpha Laval 50 point rotary parlour, Lancashire, England, April

5TH SBKF (SHELL BUCKLE KNOCKDOWN FACTOR) WORKSHOP, MSFC, FEB. 3-4, 2015

STS-335 STS-135 ATLANTIS ENGINE-3 (LAST) INSTALLATION

nat west media centre- lords cricket ground construction shot

Structural Heat Intercept-Insulation-Vibration Evaluation Rig, SHIVER

Title: W-8 Fan Acoustic Casing Treatment Test on the Source Diagnostic Test Rotor Alone HardwareProgram: Advanced Air Vehicles Program (AAVP)Project: Advanced Air Transport Technology (AATT)Sub-project: Aircraft Noise Reduction (ANR)Weekly Highlight:· Acoustic Casing Treatment Testing Completed in the W-8 Single Stage Axial Compressor Facility: Testing of Acoustic Casing Treatments on the Source Diagnostic Test (SDT) rotor alone hardware which had begun in early January was completed on Thursday, February 16th. Four different over-the-rotor acoustic casing treatment concepts were tested along with two baseline configurations. Testing included steady-aerodynamic measurements of fan performance, hotfilm turbulence measurements, and inlet acoustic measurements with an in-duct array. These measurements will be used to assess the aerodynamic and acoustic impact of fan acoustic casing treatments on a high bypass ratio fan at TRL 3. This test was the last of 3 planned tests of

VANDENBERG AIR FORCE BASE, Calif. - NASA's Orbiting Carbon Observatory-2, or OCO-2, satellite sits atop a United Launch Alliance Delta II rocket prior to encapsulation in its payload fairing at Space Launch Complex 2 at Vandenberg Air Force Base in California. Launch is scheduled for 2:56 a.m. PDT 5:56 a.m. EDT on July 1.OCO-2 is NASAs first mission dedicated to studying atmospheric carbon dioxide, the leading human-produced greenhouse gas driving changes in Earths climate. OCO-2 will provide a new tool for understanding the human and natural sources of carbon dioxide emissions and the natural "sinks" that absorb carbon dioxide and help control its buildup. The observatory will measure the global geographic distribution of these sources and sinks and study their changes over time.

DF-ST-89-04130. Base: Macdill Air Force Base State: Florida (FL) Country: United States Of America (USA)

ARES 7 AXIS MILLING EQUIPMENT AND FACILITIES.

Man welding large steel tank in factory

KENNEDY SPACE CENTER, FLA. -- In the Orbiter Processing Facility bay 2, technicians work around the attach point for the external tank near Endeavour's landing gear. The orbiter is scheduled to fly on mission STS-118 to the International Space Station in the summer of 2007.

The Soyuz TMA-5 spacecraft is mated to its booster rocket in a processing hangar at the Baikonur Cosmodrome in Kazakhstan Monday, October 11, 2004, in preparation for its rollout to the launch pad October 12 and its liftoff October 14 to carry Expedition 10 Commander and NASA Science Officer Leroy Chiao, Flight Engineer and Soyuz Commander Salizhan Sharipov and Russian Space Forces cosmonaut Yuri Shargin to the International Space Station.

Interior View of Orbiter Processing Facility 3

Space Launch System Corestage-2 Liquid Hydrogen(LH2) tank is under construction at NASA's Michoud Assembly Facility. Here you can see 1 of 5 barrels being loaded in the Vertical Assembly Center tool where it will be welded.

Inside the Rotation, Processing and Surge Facility at NASAs Kennedy Space Center in Florida, technicians inspect the Space Launch Systems (SLS) right-hand aft skirt prior to mating it with the rockets right-hand motor segment - one of five segments that make up one of two solid rocket boosters - on June 24, 2020. Once the two aft skirts are mated to the aft segments, they will be moved to the Vehicle Assembly Building for stacking on the mobile launcher. Manufactured by Northrop Grumman in Utah, the twin boosters provide more than 75 percent of the total SLS thrust at launch. Under the Artemis program, NASA will land the first woman and the next man on the Moon by 2024. The first in a series of increasingly complex missions, Artemis I will test the Orion spacecraft and SLS as an integrated system ahead of crewed flights to the Moon.

Drinking water pipes leading to to the reservoir in the city of Munich in the Forstenrieder Park, Munich, Bavaria, Germany, Europe

In the Integration Facility at the Baikonur Cosmodrome in Kazakhstan, the Soyuz TMA-10M spacecraft is prepared for encapsulation into the third stage of a Soyuz booster rocket Sept. 19. The Soyuz spacecraft will move to its launch pad Sept. 23 for final preparations for launch Sept. 26, Kazakh time, to carry Expedition 37/38 Flight Engineer Michael Hopkins of NASA, Soyuz Commander Oleg Kotov and Flight Engineer Sergey Ryazanskiy into orbit for the start of a five and a half month mission on the International Space Station.NASA/Victor Zelentsov

Opening in steel pipe

KENNEDY SPACE CENTER, FLA. -- The external tank for Endeavour is being lifted from the checkout cell inside the Vehicle Assembly Building for mating with the solid rocket boosters. Endeavour is currently targeted for rollover to the VAB July 5. Endeavour is the designated orbiter for mission STS-118, targeted for launch on Aug. 9 to the International Space Station. The mission will continue space station construction by delivering a third starboard truss segment, S5, as well as carrying the external stowage platform 3.

Interior of Dallas Dam Powerhouse, Columbia River, Oregon, USA

of 4